View SM200P81_7855652.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

data sheet rf engine ? part number s: sm200 p 8 1 and rf200p81 model sm 2 00 sm200pu1 and rf200pu1 document revision v1. 3 ? 20 1 2 synapse wireless , all rights reserved all synapse products are patented or patent pending specifications are subject to change without notice ? confirm that data is current synapse, the synapse logo, snap, and portal are all registered trademarks of synapse wireless, inc. 500 discovery drive hunts ville, alabama 35806 877 - 982 - 7888 doc # 4301 45 - 01 b
model sm200 data sheet ? document number 430145- 01 b ? page 2 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com
model sm200 data sheet ? document number 430145- 01 b ? page 3 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com table of contents 1.0 rf engine model sm200 oem modules overview ......................................................... 4 1.1 specifications ............................................................................................................. 5 1.2 pin defini tions ........................................................................................................... 6 1.3 rf module pin compatibility .................................................................................... 8 1.4 electrical characteristics ........................................................................................... 9 1.5 mechanical drawings .............................................................................................. 11 1.6 board mounting considerations .............................................................................. 13 1.6.1 processing .................................................................................................... 13 1.6.2 pb - free soldering paste ............................................................................... 14 1.6.3 cleaning ....................................................................................................... 14 1.6.4 optical inspection ........................................................................................ 14 1.6.5 repeating reflow soldering ........................................................................ 14 1.6.6 wave soldering ............................................................................................ 14 1.6.7 hand soldering ............................................................................................ 15 1.6.8 rework ......................................................................................................... 15 1.6.9 additional grounding .................................................................................. 15 2.0 ag ency certifications ....................................................................................................... 15 2.1 united states (fcc) ................................................................................................. 15 2.1.1 oem labeling requirements ...................................................................... 16 2.1.2 fcc notices ................................................................................................. 16 2.1.3 fcc approved antennas ............................................................................. 17 2.2 canada (ic) .............................................................................................................. 19 2.2.1 ic approved antennas ................................................................................ 19 2.2.2 oem labeling requirements ...................................................................... 21
model sm200 data sheet ? document number 430145- 01 b ? page 4 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com 1.0 rf engine model sm200 oem modules overview the rf engine model sm200 includes the sm 200p81 , sm200pu1, rf200p81 and rf200pu1 part numbers. they are ieee 802.15.4, low power, highly - reliable solution s to embedded wireless control and monitoring network needs that require high data rates. the model sm 200 embed s synapse?s snap os, the industry?s first internet - enabled, wireless me sh network operating system into the atmel atmega128rfa1 single - chip avr? microcontroller with an integrated transceiver that delivers up to 2mbits/sec. these low - cost mod ules can have power consumption as low as 0.25 a to enable a new generation of batte ry - driven systems. snap?s on - board python interpreter provides for rapid application development and over - the - air programming, while atmel?s low - power rf single - chip design saves board space and lowers the overall bill of materials and power consumption. the model sm 200 modules are approved as an fcc part 15 unlicensed modular transmitter s , as well as having ce certification and ic certification . the modules provide up to 16 channels of operation in the ism 2.4ghz frequency band. data sheet covers part number s sm200 p81 /pu1 and rf200p81 /pu1 : ? SM200P81 /pu1 : 38 gpio and up to 7 a/d inputs ? rf200p81 /pu1 : 20 gpio and up to 7 a /d inputs ? 128k f lash, 58.5 k free for over - the - air uploaded user apps ? two uart ports for control or transparent data ? low power modes: 0.25 a with internal timer running ? spread spectrum (dsss) technology surmounts noisy environments ? up to 2 mbps data rate ? 2.4 ghz rf frequency ? receive sensitivity - 100dbm at 250kbps ? transmit power 3 dbm ? integrated chip antenna or u.fl connecter ? SM200P81 /pu1 : s older - able ? rf200p81/pu1: solder - able, socket - able
model sm200 data sheet a document number 430145 - 01 b a page 5 of 21 ?2012 synapse wireless, inc. a 500 discovery drive, huntsville, al 35806 a 256 - 852 - 7888 a synapse - wireless.com figure 1.0 block diagram showing the major subsystems comprising model sm200 1.1 specifications table 1.0 specifications SM200P81 /pu1 rf200p81 /pu1 performance outdoor los range up to 15 00 /2500 f ee t at 250kb ps transmit power output 3 dbm rf data rate 2 50kbps , 500kbps, 1mbps, 2mbps receiver sensitivity - 100 dbm (1% per , 250kbps ) power requirements supply voltage 1.8 - 3.6 v transmit current (typ@3.3v) 22.5 ma idle/receive current (typ@3.3v) 20 .5 ma power - down current (typ@3.3v) 0.25 ua general frequency ism 2.4 g hz spreading method direct sequence (dsss) modulation o - qpsk dimensions 29.8mm x 19mm 33.86 mm x 33.86 mm operating temperature - 40 to 85 deg c. antenna options integrated chip antenna / external antenna networking topology snap error handling retries and acknowledgement number of channels 16 available i/o uarts with hw flow control 2 ports - 8 total i/o gpio 38 total; 7 can be analog - in with 10bit adc 20 total; 7 can be analog - in with 10bit adc agency approvals ce certified yes yes fcc part 15.24 9 fcc id: u9o - sm200 fcc id: u9o - sm200 industry canada (ic) ic: 7084a - sm200 ic: 7084a - sm200
model sm200 data sheet ? document number 430145- 01 b ? page 6 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com 1.2 pin definitions table 1.1 sm200 p81/pu1 and rf200 p81/pu1 pin assignments sm200 pin rf200 pin pin name snappy io pin description a1 1, 24 gnd power supply a2 21 vcc pow e r supply a3 21 vcc pow e r supply a4 13 pf0_adc0 24 io or analog0 a5 15 pf2_adc2_dig2 26 io or analog2 or spi clk or antenna diversity control a6 17 pf4_adc4_tck 28 io or analog4 or jtag test clock a7 19 pf6_adc6_tdo 30 io or analog6 or jtag test data out or i 2 c sda a8 1, 24 gnd power supply b1 16 pe2_xck0_ain0 18 io or spi miso or analog comparator or external clock b2 22 pe3_oc3a_ain1 19 io or a na lo g comparator or p wm or output compare matc h 1 b3 8 pe5_oc3c_int5 21 io or uart0 rts input or pwm or interrupt b4 14 pf1_adc1 25 io or analog1 or spi mosi b5 pg1_dig1 33 b6 18 pf5_adc5_tms 29 io or analog5 or jtag test mode select b7 20 pf7_adc7_tdi 31 io or analog7 or jtag test data in or i 2 c s c l b8 1, 24 gnd power supply c1 5 pe0_rxd0_pcint8 16 io or uart0 data in or interrupt c2 6 pe1_txd0 17 io or uart0 data out c3 7 pe4_oc3b_int4 20 io or uart0 cts output or pwm or interrupt c4 pe6_t3_int6 22 c5 12 pe7_icp3_int7_clk 0 23 io or uart1 rts input or clock output buffer or interrupt c6 nc c7 nc c8 1, 24 gnd pow e r supply d1 4 pb5_oc1a_pcint5 5 io or pwm or interrupt d2 3 pb6_oc1b_pcint6 6 io or pwm or interrupt d3 2 pb7_oc0a_oc1c_p cint7 7 io or pwm or interrupt d4 nc d5 nc d6 nc d7 nc
model sm200 data sheet ? document number 430145- 01 b ? page 7 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com SM200P81 pin rf200p81 pin pin name snappy io pin description d8 1, 24 gnd power supply e1 pb2_mosi_ pcint2 2 2 io or hardware spi mosi or interrupt e2 pb3_miso_ pcint3 2 3 io or hardware spi miso or interrupt e3 pb4_oc2a_pcint4 4 io or pwm or interrupt e4 nc e5 nc e6 nc e7 nc e8 rf out 50 ohm rf output on specially ordered devices f1 pb0_ssn_pcint0 2 0 io or hardware spi select or interrupt f2 pb1_sck_pcint1 2 1 io or hardware spi clock or interrupt f3 pd1_sda_int1 2 9 io or hardware i2c or interrupt f4 pd0_scl_int0 2 8 io or hardware i2c or interrupt f5 nc f6 nc f7 nc f8 1, 24 gnd power supply g1 clki must be pulled low during normal operation g2 pd7_t0 15 g3 11 pd4_icp1 12 io or uart1 cts output or input capture g4 9 pd2_rxd1_int2 10 io or uart1 data in or interrupt g5 pg5_oc0b 37 io or pwm g6 nc g7 nc g8 1, 24 gnd power supply h1 1, 24 gnd power supply h2 pd6_t1 14 io or timer/counter1 clock input h3 pd5_xck1 13 io or usart1 external clock input/output h4 10 pd3_txd1_int3 11 io or uart1 data out or interrupt h5 23 reset# module r e s e t, active low h6 tst must be pulled low during normal operation h7 nc h8 1, 24 gnd power supply 1 ot h e r snap en g i n es h a v e a d e b u g co nnec t i o n on p in 2 2 . t h e arc h itecture of t h e rf200 r e quir e s m u lt ip le d e b u g c o n n ectio n s, w h ich c o m e out o n o t h er p i n s. rat h er t h an lea v e p i n 22 u seless, it is a v ailable as an add itio n al gpio o r ana l og co m p arator. this will not be d i rectly accessible on synapse deve l opm ent b o ards, but c u stom circuit designs have the p i n a v ailable for s p ecialized purpos e s. 2 these pins have special i 2 c and spi hardware that is not natively supported by snap. you could use peek and poke to initialize and enable this hardware functionality. use at your own risk!
model sm200 data sheet ? document number 430145- 01 b ? page 8 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com 1.3 rf module pin compatibility table 1.1. SM200P81 /pu1 module pin assignments rf200 pin sm200 pin name description 1 a1 , a8, b8, c8, d8, f8, g8, h1, h8 gnd power supply 2 d3 gpio0/oc0a/oc1c/pcint7/pb7 gpio_0, pwm, or interrupt 3 d2 gpio1/oc1b/pcint6/pb6 gpio_1, pwm, or interrupt 4 d1 gpio2/oc1a/pcint5/pb5 gpio_2, pwm, or interrupt 5 c1 gpio3/rxd0/pcint8/pe0 gpio_3, interrupt, or uart0 data input 6 c2 gpio4/txd0/pe1 gpio_4, uart0 data output 7 c3 gpio5/oc3b/int4/pe4 gpio_5, pwm, interrupt, or uart0 cts output 8 b3 gpio6/oc3c/int5/pe5 gpio_6 , pwm, interrupt, or uart0 rts input 9 g4 gpio7/rxd1/int2/pd2 gpio_7, interrupt, or uart1 data input 10 h4 gpio8/txd1/int3/pd3 gpio_8, interrupt, or uart1 data output 11 g3 gpio9/icp1/pd4 gpio_9, or uart1 cts output 12 c5 gpio10/icp3/int7/clk0 /pe7 gpio_10, interrupt, clock output, or uart1 rts input 13 a4 gpio11/adc0/pf0 gpio_11, or analog in 14 b4 gpio12/adc1/pf1 gpio_12, spi mosi, or analog in 15 a5 gpio13/adc2/dig2/pf2 gpio_13, spi sclk, antenna diversity, or analog in 16 b1 gpio14/xck0/ain0/pe2 gpio_14, spi miso, usart clk, analog comparator, or analog in 17 a6 gpio15/adc4/tck/pf4 gpio_15, jtag tck, or analog in 18 b6 gpio16/adc5/tms/pf5 gpio_16, jtag tms, or analog in 19 a7 gpio17/adc6/tdo/pf6 gpio_17, jtag tdo, i2c sda, or analog in 20 b7 gpio18/adc7/tdi/pf7 gpio_18, jtag tdi, i2c scl, or analog in 21 a2, a3 vcc power supply 22 b2 gpio19/oc3a/ain1/pe3 gpio_19, pwm, analog comparator 23 h5 reset module reset, active low 24 a1, a8, b8, c8, d8, f8, g8, h1, h8 gnd power supply
model sm200 data sheet ? document number 430145- 01 b ? page 9 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com 1.4 electrical characteristics table 1.2. dc characteristics symbol parameter condition min typ max 1 units v cc supply voltage 2 1.8 3.3 3.6 v t operating temp op - 40 85 c v input hi voltage ih all digital inputs v cc - 0.4 v v input low voltage il all digital inputs 0.4 v v output low voltage ol all drive strengths (2,4,6,8 ma) 0.4 v v output high voltage oh all drive strengths (2,4,6,8 ma) v cc - 0.4 v il in leakage current in v in =v cc or v ss , all pins <10na 1 ua tx - i transmit current cc v cc = 3.3v p tx =3dbm 14.5 3 ma rx - i receive current cc v cc = 3.3v 12.5 3 ma shdn - i sleep current cc v cc = 3.3v 0.25 ua 1 all typical specifications are measured at 25c. 2 absolute maximum stress rated voltage for vcc is - 0.3 to 3.6. it is recommended that a bulk decoupling capacitor (47 uf tantalum rated at 6.3volts) be located close to the vcc pin 21 of the sm200 connector on host board. 3 2.4ghz transceiver current only. d oes not include current required to run cpu . table 1.3. adc electrical characteristics (operating) symbol parameter condition min typical max unit v refh voltage reference, high 3 programmable 1.5 1.6 1.8 v v analog input voltage indc single ended 0 1.8 v differential 0 4 3.3 3 v refh is programmable to three fixed values; 1.5v, 1.6v, and 1.8v. the default is 1.6v. 4 each differential analog input may be as high as 3.3v but the single - ended voltage is still limited to the voltage reference. table 1.4. adc timing/performance characteristics symbol parameter condition min typical max unit r source impedance at input as 5 3k k ? res conversion resolution single ended clkadc <= 4mhz 10 bits single ended clkadc > 8mhz 8 dnl differential non - linearity v refh = 1.6v clkadc=4mhz - 0.5 lsb inl integral non - linearity v refh = 1.6v clkadc=4mhz 0.8 lsb e zero - scale error zs 1.5 lsb e gain error g 1 lsb 5 any analog source with a source impedance greater the 3k ? will increase the sampling time.
model sm200 data sheet ? document number 430145- 01 b ? page 10 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com table 1.5 . reset, brown - out and internal voltage characteristics symbol parameter condition min typical max unit v power - on reset threshold voltage (rising) pot(rising) power supply fully discharged 1.6 v v power - on reset threshold voltage (falling) pot(falling) 0.05 0.3 v t power - on reset recovery time pot time of evdd/devdd < v 1.0 pot ms v power - on slope rate psr 1.8 3300 v/ms v rstn pin threshold voltage rst 0.1v dd 0.9 v v dd t minimum pulse width on rstn pin rst 200 300 ns v brown - out detector hysteresis hys 7.5 50 mv t min pulse width on brown - out reset bod 100 ns contact atmel for additional details
model sm200 data sheet ? document number 430145- 01 b ? page 11 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com 1.5 mechanical drawings these d rawings in figure 1. 1 and 1.2 show the modules with the option of the integrated chip antenna or u.fl connector. download figure 1.1, SM200P81 /pu1 mechanical drawing in pdf , dxf , or dft format.
model sm200 data sheet ? document number 430145- 01 b ? page 12 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com download figure 1.2, rf200p81 /pu1 mechanical drawing in pdf , dxf , or dft format.
model sm200 data sheet ? document number 430145- 01 b ? page 13 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com 1.6 board mounting considerations 1.6.1 processing table 1.5 recommended reflow profile parameter value ramp up rate (from tsoakmax to tpeak) 3o/sec max minimum soak temperature 150oc maximum soak temperature 200oc soak time 60 - 120 sec tliquidus 217oc time above tl 30 - 6 0 sec (recommended: 40 sec) tpeak 230 o - 250oc (recommended: 235 o c) time within 5o of tpeak 20 - 30 sec time from 25o to tpeak 8 min max ramp down rate 6oc/sec max achieve the brightest possible solder fillets with a good shape and low contact angle.
model sm200 data sheet ? document number 430145- 01 b ? page 14 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com 1.6.2 pb - free soldering paste use of ?no clean? soldering paste is strongly recommended, as it does not require cleaning after the soldering process . 1.6.3 cleaning in general, cleaning the populated modules is strongly discouraged. residuals under the module cannot be easily removed with any cleaning process. ? cleaning with water can lead to capillary effects where water is absorbed into the gap between the host boa rd and the module. the combination of soldering flux residuals and encapsulated water could lead to short circuits between neighboring pads. water could also damage any stickers or labels. ? cleaning with alcohol or a similar organic solvent will likely fl ood soldering flux residuals into the two housings, which is not accessible for post - washing inspection. the solvent could also damage any stickers or labels. ? ultrasonic cleaning could damage the module permanently. the best approach is to consider usi ng a ?no clean? soldering paste and eliminate the post - soldering cleaning step. 1.6.4 optical inspection ? after soldering the module to the host board, consider optical inspection to check the following: ? proper alignment and centering of the module over the pads. ? proper solder joints on all pads. excessive solder or contacts to neighboring pads, or vias. 1.6.5 repeating reflow soldering only a single reflow soldering process is encouraged for host boards. 1.6.6 wave soldering if a wave soldering process is required on the host boards due to the presence of leaded components, only a single wave soldering process is encouraged.
model sm200 data sheet ? document number 430145- 01 b ? page 15 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com 1.6.7 hand soldering hand soldering is possible. use a soldering iron temperature setting equivalent t o 350c, follow ipc recommendations/ reference document ipc - 7711 . 1.6.8 rework the model sm700 module can be unsoldered from the host board. use of a hot air rework tool and hot plate for pre - heating fr om underneath is recommended. avoid overheating. warning : never attempt a rework on the module itself (e.g. replacing individual components). such actions will terminate warranty coverage. 1.6.9 additional grounding attempts to improve module or system grounding by soldering braids, wires, or cables onto the module rf shield cover is done at the customers own risk. the numerous ground pins at the module perimeter should be sufficient for optimum immunity to external rf interference. 2.0 agency certificat ions 2.1 united states (fcc) the model sm 200 module compl ies with part 15 of the fcc rules and regulations. compliance with the labeling requirements, fcc notices and antenna usage guidelines is required. in order to comply with fcc certification requirements, the original equipment manufacturer (oem) must fulfil l the following requirements. 1. the system integrator must place an exterior label on the outside of the final product housing the sm 200 modules. figure 2. 1 shows the contents that must be included in this label. 2. sm 200 modules may only be used with the ant enna that has been tested and approved for use with the module. please refer to the antenna table provided in this section.
model sm200 data sheet ? document number 430145- 01 b ? page 16 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com 2.1.1 oem labeling requirements notice: the oem must make sure that fcc labeling requirements are met. this includes a clearly visible exterior label on the outside of the final product housing that displays the contents shown in figure 2. 1. 2.1.2 fcc notices warning: the sm 200 modules have been tested by the fcc for use with other products without further certification (as per fcc section 2.1091). changes or modifications to this device not expressly approved by synapse wireless inc. could void the user?s authority to operate the equipment. notice: oem?s must certify final end product to comply with unintentional radiators (fcc section 15.107 and 15.109) before declaring compliance of their final product to part 15 of the fcc rules. this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. these limits are designed to provide reasonable protection against harmful interference in a residential installation. this equipment generates, uses, and can ra diate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. however, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ? reorient or rel ocate the receiving antenna. ? increase the separation between the equipment and receiver. ? connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ? consult the dealer or an experienced radio/tv techni cian for help . manufacturers name figure 2.1 fcc label brand name or trade name model: cont ains model sm200 fcc id: u9o - sm200 this device complies with part 15 of the fcc rules. operation is subject to the following two conditions: (1) this device may not cause harmful interferences, and (2) this device must accept any interference received, including interference that may cause undesired operation.
model sm200 data sheet ? document number 430145- 01 b ? page 17 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com 2.1.3 fcc approved antennas notice: to reduce potential radio interference to other users, the antenna type and its gain should be chosen so that the equivalent isotropically radiated power (e.i.r.p . ) is not more than that permitted for success ful commu nication. this module has been designed to operate with the antennas listed in table 2.1 .3 . the required antenna impedance is 50 ohms. table 2.1. 3 a sm/rf200p81 approved fcc antennas part number type gain application min. separation murata lda312g4413h - 280 chip - 2.3 dbi fixed/mobile 20 cm. table 2.1. 3b sm/rf200pu1 approved fcc antennas part number type gain application min. separation pulse w1027 dipole (quarter - wave rpsma) 3.2 dbi fixed/mobile 20 cm.
model sm200 data sheet ? document number 430145- 01 b ? page 18 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com
model sm200 data sheet ? document number 430145- 01 b ? page 19 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com 2.2 canada (ic) this device complies with industry canada license - exempt rss standard(s). operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause u ndesired operation of the device. le prsent appareil est conforme aux cnr d'industrie canada applicables aux appareils radio exempts de licence. l'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. under industry canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by industry canada. to reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e. i.r.p.) is not more than that necessary for successful communication. conformment la rglementation d'industrie canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur p ar industrie canada. dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'i ntensit ncessaire l'tablissement d'une communication satisfaisante. 2.2.1 ic approved antennas this radio transmitter model: sm 20 0 , ic: 7084a - sm 200 has been approved by industry canada to operate with the antenna types listed below with the maximum permis sible gain and required antenna impedance for each antenna type indicated. antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. le prsent metteur radio model: sm200, ic: 7084a - sm200 a t approuv par industrie canada pour fonctionner avec les types d'antenne numrs ci - dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. les types d'antenne non inclus dan s cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur.
model sm200 data sheet ? document number 430145- 01 b ? page 20 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com table 2.2 . 1 a approved ic antennas part number type gain application min. separation murata lda312g4413h - 280 chip - 2.3 dbi fixed/mobile 20 cm. table 2. 2 . 1b approved fcc antennas part number type gain application min. separation pulse w1027 dipole (quarter - wave rpsma) 3.2 dbi fixed/mobile 20 cm.
model sm200 data sheet ? document number 430145- 01 b ? page 21 of 21 ?2012 synapse wireless, inc. ? 500 discovery drive, huntsville, al 35806 ? 256- 852- 7888 ? synapse - wireless.com 2.2.2 oem labeling requirements labeling requirements for industry canada are similar to those of the fcc. a clearly visible label on the outside of the final product housing must display the contents shown in figure 2 . 2. note: the oem can choose to implement a single label combined for both fcc and ic labeling requirements. if a combined single label is chosen, there must be a clearly visible label on the outside of the final product ho using displaying the contents shown in figure 2. 3. manufacturers name figure 2.2 ic label brand name or trade name model: contains model sm200 ic: 7084a - sm200 manufacturers name figure 2.3 combined fcc and ic label brand name or trade name model: contains model sm200 fcc id: u9o - sm200 contains model sm200 ic: 7084a - sm200 this device complies with part 15 of the fcc rules. operation is subject to the following two conditions: (1) this device may not cause harmful interferences, and (2) this device must accept any interference received, including interference that may cause undesired operation.

▲Up To Search▲

Price & Availability of SM200P81

	To Download SM200P81 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .